Sikama Falcon UP4000 Updated computer 12 zone conduction/convection/cooling

Description

Used Sikama Falcon UP4000 MFG 2003 3 phase  I saw this unit running a few months ago, but have not tested it myself. It comes with a lap top, a chiller, a separate exhaust fan, and a manuaI with floppys. Just copied hard drive and updated computer,  software is coming up as it should and should be good for years now.  Can be skidded and wrapped at my craters, estimated skid size
56x48 0 pick up from Crater at 85040 Manufacturer Specs Below and UP 2000 specs at very bottom explaining base system better
Ultra Profile 4000
Overview
If the seven zones of the Ultra Profile 2000 aren’t enough to create the profiles you need, SIKAMA’s twelve-zone Ultra Profile 4000 is the machine you’re looking for. Using the same Conduction+Convection technology as the Ultra Profile 2000, the 4000 is available in a manually operated version, and two automated versions.
The twelve zones comprise a cooled loading platform, seven Conduction+Convection heat zones, three top and bottom liquid-cooled zones, and a liquid-cooled offload platform. Each top and bottom stage combines independent set point controls for precise temperature controls and exceptional profile flexibility. The Ultra Profile shares many of the same features as the Ultra Profile 2000 and will reflow the same types of components and substrates. Balanced heating and cooling ensures cost-efficient operation, translating into production savings for your operation.
Heating Zones
7
Cooling Zones
4
Loading Zones
1
Total Number of Zones
12
Platen Size
4.5 in. x 12 in. (114 x 305 mm)
Maximum Substrate Size
3.9 in. x 12 in. (100 x 305 mm)
Time Mode (Dwell & Travel Time)
7 sec. to 99 min. 59 sec. (per zone)
Temperature (Standard)
Up to 400°C
Temperature Accuracy
± 2°C
Warm-up Time to 230°C
15 minutes
Coolant Flow
0.5 to 2 GPM (2 to 8 liters/min.)
Alarms
Over/Under Temperature, Gas, Coolant, Motor Torque, SMEMA Interface
Parts Flow (Specify When Ordering)
L to R or R to L, Back to Front or Front to Back
Gas Consumption
500-600 cubic feet per hour
O2 Level
10 PPM, 0.25 inch opening
Voltage (Specify when Ordering)
200 to 240 VAC, 50/60 Hz, 1 or 3 Phase
Start-up Power (Kw)
17kW @ 240 VAC
Power Consumption
50% or less
Basic Unit Weight
750 lbs. (340 Kg)
Basic Unit Dimensions
Inline: L 72 x W 24 x H 54 inches (183 x 61 x 137 cm)
Serpentine: L 72 x W 38 x H 56 inches (183 x 97 x 142 cm)
System serial number must accompany spare parts order
Overview
SIKAMA’s seven-zone Ultra Profile 2000 features our patented Conduction+Convection technology, combined with a cooled loading platform, four Conduction+Convection heat zones, a top and bottom liquid-cooled zone, and a liquid-cooled offload platform. Inert gas (air, nitrogen, or forming gas) surrounds the components from the top and bottom, then exits at the sides to prevent contamination of adjoining zones and eliminating flux buildup. Precise temperature controls and independent set point controls for each stage provide excellent profile flexibility.
The Ultra Profile 2000 is available as a manually loaded stand-alone system, or an automated system with a SMEMA interface, robotics, and sensors that allows you to link it to other automated assembly machines in your production line. Parts can be transported by the sweeperbars with a cycle time of less than 10 seconds. Its 400° C maximum temperature gives the Ultra Profile 2000 the flexibility to handle die soldering, BGAs, Flip Chips, and IMS with copper or aluminum bases, as well as high density components. Reflow soldering to copper, beryllium, ceramic, and glass epoxy substrates are all possible with the Ultra Profile 2000.
Economy of operation is ensured by SIKAMA’s patented balanced heating and cooling technology, with a nitrogen usage of 200 to 400 CFHg. All this capability comes with a small 38 by 43-inch footprint, which means the Ultra Profile 2000 will fit easily onto your production floor or clean room.